## Circuit lm317 voltage regulator circuit power supply

Circuit lm317 voltage regulator circuit adjustable power supply. Circuit regulated power supply, adjustable from 1.2 to 30V/1.5A with the ic regulator lm317T use to substitute eliminator of piles and batteries in your circuits.

This power supply uses the LM317T integrated circuit, which allows the output voltage to be varied between 1.2 and 30V with currents up to 1.5 Amps. To be used as a battery and battery eliminator in most applications.

Unlike complicated transistor sources, this is an excellent choice for anyone who wants an adjustable power supply with a current capacity of up to 1.5 amperes. The CI lm317 is low cost and can be found with facilities in electronics stores.
In the AC connectors, you must connect a 24 volt transformer with a current capacity of at least 1.5 amperes.
The transformer that will determine the maximum voltage obtained at the output of the power supply, in this way you must choose a transformer that meets your needs.
To find out which transformer you need, make a simple account:
Tt = (Tm / 1.4142) + 2
Tt: Voltage in the Transformer
Tm: Maximum voltage
Example, I need an adjustable power supply up to 24V
Tf = (24 / 1.4142) +2 = 18.97
Then we will use a transformer with commercial value of 20VAC.

For other calculations, see this calculator for Windows

The bridge rectifier bridge accepts equivalents from 2A / 200V, such as RS207, KBL404, KBL405, KBL406, KBL407, MDA970A5, FBU4D, FBU4F, FBU4G, KBP304, KBP305, KBP306, KBP307, Ts4b05g, Kbu808.

Modifications to the power supply circuit with lm317t
To fine voltage adjustment, uses a 220 Ω potentiometer in series with the potentiometer of 4.7k.
Connect a voltmeter to the output to determine the voltage. Or use the multimeter.
You can use this source with fixed voltage, to power certain equipment, example 17.8 volts per 1 Ampere.
You can use 2 or 3 LM317 to increase current capacity up to 4 amps, use resistors of 0.22 Ω 10 W at the output of each lm317.

### Suggestion for printed circuit board for power supply lm317

The LM317 device is an adjustable three-terminal positive-voltage regulator capable of supplying more than 1.5 A over an output-voltage range of 1.25 V to 37 V. It requires only two external resistors to set the output voltage. The device features a typical line regulation of 0.01% and typical load regulation of 0.1%. It includes current limiting, thermal overload protection, and safe operating area protection. Overload protection remains functional even if the ADJUST terminal is disconnected.

The LMx117HV is an adjustable 3-terminal positive voltage regulator capable of supplying 1.5 A or more currents over a 1.25-V to 57-V output voltage range. It requires only two external resistors to set the output voltage. The LMx17HV is packaged in standard transistor packages that are easily mounted and handled.

The LM317HV offers overload protection like current limit, thermal overload protection and safe area protection, which make the device blowout proof. The overload protection circuitry remains fully functional even if the adjustment terminal is disconnected.

Typically, no capacitors are needed unless the device is situated more than 6 inches from the input filter capacitors, in which case an input bypass is needed. An optional output capacitor can be added to improve transient response. The adjustment terminal can be bypassed to achieve very high ripple rejection ratios which are difficult to achieve with standard 3-terminal regulators.

Since the regulator is floating and sees only the input-to-output differential voltage, supplies of several hundred volts can be regulated as long as the maximum input to output differential is not exceeded, or in other words, do not short the output to ground.

By connecting a fixed resistor between the adjustment and output, the LM317HV can also be used as a precision current regulator. Supplies with electronic shutdown can be achieved by clamping the adjustment terminal to ground, which programs the output to 1.25 V, where most loads draw little current.

#### BOM  for assembling an adjustable power supply.

Last Update: 21/11/2021 20:29

 Part Value Description Quantity Resistors 1/4W R1 4.7k/ 0,5W Yellow, violet, red, gold 1 R2 220 Red, brown, gold, gold 1 Capacitors C1 2.200µF/50V Electrolytic Capacitor 1 C2, C5 100nF/50V Ceramic Capacitor 2 C3 10µF/50V Electrolytic Capacitor 1 C6 470µF/50V Electrolytic Capacitor 1 Semiconductors D1, D2, D3, D4, D5, D6 1N4004 Semiconductor diode 6 IC1 LM317 Adjustable positive voltage regulator integrated circuit. 1 LED1 Led Red or another color 5 mm led 1 Miscellaneous POT 4.7K Simple Potentiometer 1 CN1 AC Terminal block 2 pin 5.08 mm 1 CN2 OUT Terminal block 2 pin 5.08 mm 1 Printed circuit board, solder, wires, knob, transformer as designate, housing, heatsink for the Lm317, etc.

Buy kits LM317 DIY in Aliexpress with free Shipping in the Worldwide.

Click on a star to rate it!

Average rating {{avgRating}} / 5. Vote count: {{voteCount}}
{{successMsg}} {{#errorMsg}} {{.}} {{/errorMsg}}
There was an error rating this post!

Average rating 4.6 / 5. Vote count: 16

No votes so far! Be the first to rate this post.

Xtronic.org blog author. Electronics technician for the technical school of Brasilia - Brazil. Interested in electronics, circuits and technology in general.
Share:

### 10 thoughts on “Circuit lm317 voltage regulator circuit power supply”

1. Works great as a battery eliminator in a Vacuum Tube Volt Meter (VTVM) to replace the 1.5v battery used for Ohms readings. Runs off of the 6.3vac filament winding of the transformer with no issues, and a 200 ohm pot gives a nice range of adjustment for the 1.5v range..

2. I cannot find a 4.7k potentiometer
I only have 5k and 10k
So what if I replace R2(220) so that I can use one of them instead?
Will it work?
//if ‘yes’ then how?

• Hello Augusto
5K ok!
Or combine change R2 (220)

3. qual tamanho da largura e altura da placa

4. Guys , berapa tegangan maksimum dari trafo jika menggunakan trafo CT, terimakasih

• Hello Tumpur
27VAC, single.
13,5VAC: CT.

5. Good day
Thank you for this circuit. I made everything exactly like this one, except I used a GBL206 rectifier. I use a 18v transformer. My problem is that when I turn it on, the led does not come on, and the resistor R2 burns. I think the lm317 is also shorted now. How many watts should R2 be, or what am I doing wrong? Also checked for shorts.
Thanks again