TDA2005 amplifier circuit diagram 20w Bridge

| | , , ,

TDA2005 amplifier circuit diagram 20w Bridge, The TDA2005 is a class B dual audio power amplifier in Multiwatt11 package specifically designed for car radio applications. Power booster amplifiers can be easily designed using this device that provides a high current capability (up to 3.5 A) and can drive very low impedance loads (down to 1.6 Ω in stereo applications) obtaining an output power of more than 20 W (bridge configuration).

High output power : PO = 10 + 10 [email protected] =2Ω, d = 10% ; PO = [email protected] =4Ω, d=1%.
High reliability of the chip and package, with additional complete safety during operation thanks to protection against :

  • Output dc and ac short circuit to ground
  • Overrating chip temperature
  • Load dump voltage surge
  • Fortuitous open ground
  • Very inductive loads
  • High output power:Po = 10 + 10 W @ RL = 2 Ω, THD = 10%
  • Po = 20 W @ RL = 4 Ω, THD = 10%.
  • Protection against:Output DC and AC short circuit to ground
  • Overrating chip temperature
  • Load dump voltage surge
  • Fortuitous open ground
  • Very inductive loads
  • Loudspeaker protection during short circuit for one wire to ground

Flexibility in use : bridge or stereo booster amplifiers with or without boostrap and with programmable gain and bandwidth.
Space and cost saving : very low number of external components, very simple mounting system with no electrical isolation between the package and the heat sink (one screw only).
In addition, the circuit offers loudspeaker protection during short circuit for one wire to ground.

In the schematic above we have the circuit diagram with bridged tda2005, at IN-1 we have the audio signal input, which connects at P1 a 100k potentiometer to make the volume adjustment. Then the DC signal is isolated from the IC input by C2 of 2.2µF.

Get new posts by email:
Follow us on social media
  • R1 of 120k – Optimizes the output symmetry, increase the value of Po max (maximum RMS power)
  • R6 and R7 – Set the gain by feedback in bridge amplifier mode
  • R3 and R4 1 Ohms – Frequency stability, changing these values may cause frequency stability.
  • C1 2.2µF-Decouples the DC voltage from the amplifier input
  • C2 2.2µF – Optimizes shutdown delay
  • C4 and C11 – 100nF and 1000µF – power supply bypass.
  • C6 10µF – Ripple rejection
  • C7 and C8 100µF – Bootstrapping
  • C9 and C10 220µF – DC input decoupling from feedback circuit
  • C3 and C5 – Frequency stability
  • TDA2005 – Bridge mode audio power amplifier integrated circuit.
  • Recommended power supply – 12 to max. 18 volts / 2 amps.

Schematic diagram for power amplifier tda2005

Tda2005 Esquema Ponte Tda2005 Amplifier, Amplifier Tda, Audio, Circuits, Power Amplifier, Tda Tda2005 Amplifier Circuit Diagram 20W Bridge
Tda2005 Power Amplifier Schematic Diagram

Suggested PCB – amplifier tda2005 Bridge

Tda2005 Power Amplifier Pcb Tda2005 Amplifier, Amplifier Tda, Audio, Circuits, Power Amplifier, Tda Tda2005 Amplifier Circuit Diagram 20W Bridge
Tda2005 Power Amplifier Pcb
Tda2005 Power Amplifier Layout Tda2005 Amplifier, Amplifier Tda, Audio, Circuits, Power Amplifier, Tda Tda2005 Amplifier Circuit Diagram 20W Bridge
Tda2005 Power Amplifier Pcb Layout

BOM for assembling the amplifier with tda2005

Last Update: 11/29/2021 13:06

PartValueDescriptionQuantity
Resistors 1/4W
R1120KBrown, red, orange, gold1
R21KBrown, black, red, gold1
R3, R41Brown, black, gold2
R52KRed, black, red, gold1
R6, R712Brown, red, black, gold2
Capacitors
C1, C22.2uF/25vBrown, red, black, gold2
C3, C5100nF (104)Ceramic Capacitor2
C4100nF (104)Capacitor film1
C610uF/25vElectrolytic capacitor1
C7, C8100uF/25vElectrolytic capacitor2
C9, C10220uF/25vElectrolytic capacitor2
C111000uF/25vElectrolytic capacitor1
Semiconductors
IC1TDA2005RAudio amplifier integrated circuit.1
Misleenaeus
CN1INJst Xh2 connector 2.54 mm pitch or equivalent.1
OUTAudio OutputTerminal block 2 pin 5.08 mm1
PWRDC power supplyTerminal block 2 pin 5.08 mm1
P1100kPotentiometer1
Solder, Wires, Housing for the circuit, PCB, heat sink for the TDA, power supply, etc.

All capacitors for 25V or higher

For a stereo version mount two identical units, and you can use a single source sized for stereo version.
Download schematic + board to be edited in Eagle

Download PDF
Mirror

Download PDF datasheet IC TDA2005 TDA2005R TDA2005T

 

Buy TDA2005 in Aliexpress with free Shipping in the Worldwide.

How useful was this post?

Click on a star to rate it!

Average rating / 5. Vote count:

No votes so far! Be the first to rate this post.

As you found this post useful...

Share on the social networks!

We are sorry that this post was not useful for you!

Let us improve this post!

Tell us how we can improve this post?

Previous

TDA2822 mono amplifier circuit bridge 2W

Circuit 22W Stereo Amplifier Using TDA1554

Next

13 thoughts on “TDA2005 amplifier circuit diagram 20w Bridge”

  1. Самым лучшим и надёжным будет типовое питание напряжением 14.4 вольта и силой тока 3-5А

    Reply

Leave a Comment