TDA2030 LM1875 Stereo Amplifier Dynamic

tda2030 lm1875 stereo dynamic amplifier

Amplifier with TDA2030, Lm1875, TDA2050, TDA2040 power amplifier stereo or Bridge, dynamic, you can use several cis and configure to work in bridge (mono) or stereo.

Circuit based on the tda2030, tda2050, tda2040 and LM1875t PDF datasheet, including optimized printed circuit board to avoid noise. The power supply will be from a symmetrical, simply using a double transformer with voltage according to the power to be used to power the amplifier.

The board can be used in 2-channel or bridged mono mode. To use in bridge, add resistor R3(BTL) of 22K to the circuit. Output to bridged mode will turn the speaker on OUTR1 and OUTL2. Audio input will be in INR. INL will not be connected at all.

Get new posts by email:
Btl Bridge Lm1875 Tda2030 Tda2030 Amplifier, Amplifier Tda, Audio, Lm1875, Lm1875 Dual Power Supply, Lm1875T, Tda, Tda2030 Amplifier, Tda2030 Amplifier Circuit, Tda2030 Pdf, Tda2030A Amp, Tda2030A Ic, Tda2050 Amplifier, Tda2050 Bridge, Tda2050 Btl, Tda2050 Chip, Tda2050 Circuit, Tda2050 Pcb, Tda2050 Pdf, Tda2050A, Tda2050L, Tda2050V Tda2030 Lm1875 Stereo Amplifier Dynamic
Bridge
Stereo Lm1875 Tda2030 Power Amplifier Tda2030 Amplifier, Amplifier Tda, Audio, Lm1875, Lm1875 Dual Power Supply, Lm1875T, Tda, Tda2030 Amplifier, Tda2030 Amplifier Circuit, Tda2030 Pdf, Tda2030A Amp, Tda2030A Ic, Tda2050 Amplifier, Tda2050 Bridge, Tda2050 Btl, Tda2050 Chip, Tda2050 Circuit, Tda2050 Pcb, Tda2050 Pdf, Tda2050A, Tda2050L, Tda2050V Tda2030 Lm1875 Stereo Amplifier Dynamic
Stereo

Maximum voltage x maximum power table for each IC

CIMax power supply (AC)Max power (W)
TDA203013 + 13VAC or 15+15 VAC for TDA2030A2X 18W @ 4Ω, 12W @ 8Ω
TDA204015 + 15 VAC2x 30W @ 4Ω 25W 0.5% DTH, 2x 12W @ 8Ω 0.5% DTH
TDA205018 + 18 VAC2x 35W @ 4Ω, 2x 30W @ 8Ω
LM187518+18 VAC 4Ω and 22+22 for 8Ω2X 20W@ 4Ω, 2x 30W @ 8Ω

LM1875 – The LM1875 is a monolithic power amplifier offering extremely low distortion and high-quality performance for consumer audio applications. The LM1875 delivers 20 watts into a 4 or 8 load on ±25V supplies. Using an 8 load and ±30V supplies, over 30 watts of power may be delivered. The amplifier is designed to operate with a minimum of external components. Device overload protection consists of both internal current limit and thermal shutdown.
TDA2030, TDA2030A – The TDA2030A is a monolithic IC in a Pentawatt package intended for use as a low-frequency class-AB amplifier. With VS max= 44 V it is particularly suited for more reliable applications without regulated supply and for 35 W driver circuits using low-cost complementary pairs.
The TDA2030A provides high output current and has exceptionally low harmonic and crossover distortion. The device incorporates a short-circuit protection system comprising an arrangement for automatically limiting the dissipated power to keep the operating point of the output transistors within their safe operating range. A conventional thermal shutdown system is also included.
TDA2040 – The TDA2040 is a monolithic integrated circuit in the Pentawatt package, intended for use as an audio class-AB amplifier. Typically, it provides 25 W output power into 4 Ω with THD = 0.5% at VS= 34 V. The TDA2040 provides high output current and has extremely low harmonic and crossover distortion. Furthermore, the device incorporates a patented short-circuit protection system comprising an arrangement for automatically limiting the dissipated power to keep the operating point of the output transistors within their safe operating range. A thermal shutdown system is also included.
TDA2050 – The TDA 2050 is a monolithic integrated circuit in a Pentawatt package, intended for use as an audio class-AB audio amplifier. Thanks to its high power capability the TDA2050 is able to provide up to 35 W true RMS power into a 4 ohm load at THD = 0%, VS = ±18 V, f = 1 kHz and up to 32 W into an 8 ohm load at THD = 10%, VS = ±22 V, f = 1 kHz.
Moreover, the TDA2050 delivers typically 50 W music power into a 4 ohm load over 1 sec at VS = 22.5 V, f = 1 kHz.
The high power and extremely low harmonic and crossover distortion (THD = 0.05% typ, at VS = ±22 V, PO= 0.1 to 15 W, RL= 8 ohm, f = 100 Hz to 15 kHz) make the device most suitable for both hi-fi and high-end TV sets.

Dynamic power amplifier schematic with ci tda2030

Amplifier Tda2030 Tda2050 Tda2040 Lm1875 Scheme
Schematic Power Audio Amplifier

Suggested printed circuit board to assemble the amplifier

Component View Bottom Tda2030 Amplifier, Amplifier Tda, Audio, Lm1875, Lm1875 Dual Power Supply, Lm1875T, Tda, Tda2030 Amplifier, Tda2030 Amplifier Circuit, Tda2030 Pdf, Tda2030A Amp, Tda2030A Ic, Tda2050 Amplifier, Tda2050 Bridge, Tda2050 Btl, Tda2050 Chip, Tda2050 Circuit, Tda2050 Pcb, Tda2050 Pdf, Tda2050A, Tda2050L, Tda2050V Tda2030 Lm1875 Stereo Amplifier Dynamic
Component View – Tda2030 Power Amplifier
Board-Bottom Lm1875 Pcb
Board-Bottom Lm1875 Tda2030A Pcb
Board-Top Tda2030 Lm1875 Stereo Dynamic Amplifier
Lm1875 Tda2030A Pcb – Top

Part List to assemble the amplifier

Lista de material para montar o amplificador

PartValueDescriptionThe amount
Capacitors*
C1, C2, C4, C5100nCeramic capacitor4
C3, C1622uFElectrolytic capacitor2
C10, C12, C13, C142.200uF to 4.700uFElectrolytic capacitor4
C15, C181uF to 10uFPolyester Capacitor2
C17, C19220nFPolyester or ceramic capacitor2
Semiconductors
B1KBL406 or equivalentbridge rectifier1
Led1Led 5 mmLed color to choose1
IC1, IC3TDA2030 (TDA2030A), LM1875 (LM1875T), TDA2050 ou TDA2040Class AB audio amplifier integrated circuit2
Resistors 1/4W 5%
R1, R8680 Ohmblue, grey, brown, gold2
R2, R3(BTL)*, R4, R9, R1022Kred, red, orange, gold5
R5, R121 Ohmbrown, black, silver, gold2
R114.7Kyellow, violet, red, gold1
Connectors
ACPower supplyTerminal block 3 pin 3.5 mm1
OUTRAudio output Right channelTerminal block 2 pin 3.5 mm1
OUTLAudio output Left channelTerminal block 2 pin 3.5 mm1
INLAudio input left channelTerminal block 2 pin 3.5 mm1
INRAudio input right channelTerminal block 2 pin 3.5 mm1
Miscellaneous
Solder, Wires, PCI, Box, Transformer, Heat Sink, etc.

Electrolytic capacitors – 25V to transformer 12+12 ou 15+15, 35V for transformer 18+18V.
Ceramic capacitor – 50,63 ou 100V.

Download image files of the PCB in PDF, PNG, and Gerber for assembly of the amplifier

Download        Mirror

Download the semiconductor PDF datasheet used in the project

How useful was this post?

Click on a star to rate it!

Average rating / 5. Vote count:

No votes so far! Be the first to rate this post.

As you found this post useful...

Share on the social networks!

We are sorry that this post was not useful for you!

Let us improve this post!

Tell us how we can improve this post?

Photo of author
About the author
Xtronic.org blog author. Electronics technician for the technical school of Brasilia - Brazil. Interested in electronics, circuits and technology in general.
Share:

2 thoughts on “TDA2030 LM1875 Stereo Amplifier Dynamic”

Leave a Comment